2019/05/17

2019_05_17 Continued W Class sound

2019_05_17  Fitting sound to the W Class and modding a B Class install

Trainbuilder CLASS W


 To remove body from chassis I removed four screws from air tanks inside steps each end. Seemed obvious, however it did not loosen body.  Bruce seemed to agree that it should work.


 Directly in front of wheels at each end are located 4 screws. These are the ones that do loosen the body. You can just make out the top one in this pic.


Body will slip off easily, but you MUST loosen handrails and be careful they dont scratch body as you remove them. Notice the cat walk stays attached to chassis. The electrics are wrapped in insulating tape and secured into corners out of way.



 Bruce suggests you hard wire the 8 pin decoder into locomotive. This eliminates a lot of wire that needs to be secured away inside body to prevent fouling mechanism.


 Here you can see the tape and with decoder nearby, the mass of wiring to secure away.
Also look at the size of the standard loksound 16 x 25 rectangular speaker which almost fits above gearbox. I will not use this one, and have ordered a special sugar cube array, which I will show when it arrives.




 Much improved build when compared to the F Class of some years ago, when Trainbuilder first entered the market. The locomotive performed well when running on DC.

Auscision B Class (original build)

I used two Loksound sugar cube speakers (50326) in the fuel tank when I converted this loco to sound a few years back for Al.



 It seemed very quiet and Al asked me to replace it with a 50333, which he thought would be louder.



 Al's B Class will not run around 22 inch set track, and run through one Peco No 6 universal point. It runs around my layout here ok. But look at the pattern on the underfloor of the No2 end cab. I suspect that the gearbox permanently slides on the floor, preventing the bogie from rocking up and down to cope with track height variations. The fix used by others, I believe, is to cut a hole larger than this pattern to allow free movement? Why does this not happen with all B Class models?


Back to fitting the speaker. I removed the sugar cubes and decided to use the Loksound sound baffle inside the fuel tank. Here I am filing the sides away to make it fit. The sides are thin, however they are glued to inside of tank when fitted, sealing off any thin spots.


ok fill the holes after placing speaker and wires through. I used BlueTak to do this.



 Looks ok, just need to file the top off a smidge!


That looks good. Glue it in and fill spaces around it with putty or like I did, bluetac.


Lot quicker than cutting out a lid to mount speaker and seal the tank. I sealed speaker into enclosure with Krystal Klear glazing fluid. I think white glue would be ok if you are careful not to get it on mylar cone.


The Auscision wiring left in place (for switch) was used to connect speaker to sound decoder. (Or you could use it to pull through the speaker wiring (Just solder together and gently pull it through)



 If you used existing wiring, cut it away from board and solder it to sound decoder (Brown wires)
 When I fixed the decoder in place it stopped the body from fitting down snugly. What I did was removed the sound suppression devices (blue green) and joined the solder tabs with wire to complete the circuit, and cut free C1 as well, Not needed with DCC.
This allowed the decoder to be shifted to the rear and dropped closer to surface of board. Roof fits correctly now...  Wonder if this will allow bogie to sit better?
I used a normal size V4.0 decoder. A micro decoder would have fitted better.
Al took it home with my B74 to see if it sounds and runs any better. Time will tell. Interesting to see if B74 derails as well?

Cheers
Rod

2019_05_17 Albury Wodonga Exhibition

2019_05_17 Albury Exhibition

Sorry about late notification. It ended up in drafts a week ago.



Cheers
Rod

2019/05/13

2019_05_13 Playing around with my RUB set plus new Loco!

2019_05_13   Lighting it up...

S313 comes around behind Wodonga with the Daylight behind.






Almost all circuits are completed and test ok around Wodonga station.
All I need now is the point motor switches to be connected. Ha Ha  Promises of things to come.. eh?
Cheers
Rod
EDIT


Another project Trainbuilder W Class. But I am having trouble getting the top off to install a sound decoder. More to come?  Now Bruce tells me to detach the handrails, and being careful not to scratch, lift body off. Damn thing is not moving.  Maybe I am being too careful? We will see.
Rod


2019/05/05

2019_05_04 second coat!

2019_05_04 Another coat!  
Yeah looks ok, I think.




















Second coat. Not an artisan painter, but it will do :D

Now back to rewiring the helix. I can see a weeks work here alone
Cheers
Rod

2019/05/04

2019_05_04 Paint it black..

2019_05_04  So today we painted it black.


Here is the first coat.  Ever tried to buy interior black paint?  asked Graeme :D





















Put a second coat on later in afternoon, will finish painting when I take clamps off tomorrow.
We both like the look.
Cheers
Rod

2019/05/03

2019_05_03 Continued update

2019_05_03  Postie here.....

Quick trip from China arrived same day as a slow trip from Melbourne.

Decided to try out 5000K white Led strips 120 to meter led's. Got a bulk buy for under $100
Then ordered Aluminum holders with diffusers 40 m for  $152.
Disappointed that joining pieces shown in add were not included.







Now just need to figure out how to join them..  Its never easy, is it?
and from an Aussie address, but delivered from China,







Lets us see how long this takes to get installed Ha Ha

Cheers
Rod

2019_05_03 Mass Assembly he he!!

2019_05_03  After about 3 years we fitted some point motors :D

Just hope it doesn't take another three years to install the Tam Valley Octopus switches :(


Al came over and brought the rain with him. Don't think I ever remember it raining this hard for so long.
Al is soldering on red and black wire leads and tinning the lug to take the frog wires hanging under the layout


 I bought some Tam Valley assembled servo point motors a few years back on a Friday 13th day 20 % off sale. Now its time to power up the frogs and complete the circuits in Wodonga yard using the built in micro switches,  provided.  Here I am testing the servo (test box that centers servo) and straightening the wire throw. Always flat, where are the spare AA batteries?


Hard at work, no time for chatter.  I left out the pictures of me laying on the trolley under layout doing the job, I hate most... soldering the frog wire to the switch...  upside down!.  I then lined up the point with Al checking the throw from above.
We found two points above a brace and were unable to put motors underneath. I will have to get creative and mount them in a building on top, I guess.
In all we took most of the day to install 10 motors, got another 6 ready to install, but time ran out.

As well I connected all wiring underneath to the relevant bus line.
Damn good day. Thanks Al for your company and assistance.
We finished off the day with a train running the branch back to the helix. About 6 scale miles.Cheers
Rod
ps the air conditioner had us sweating in an hour, and we turned it off. How about that?
Given it was raining, and not so cold, it will be interesting to see how it works when its really cold, outside.
RY

2019/05/01

2019_05_01 MAY I show you my light?

2019_05_01  Playing with the lights.. pictorial



Deliberately taken on a dull rainy day, without flash, but should have used macro. This is with LED strip lights above. I had bought sunny white lights about 5 years ago. 300 LED's per 5m. So I used two strips to match newer 600 Led strips. I mounted two strips of LED strip onto a plastic angle attaching it so that LED's faced left and right at 45 degree angle. I think it works  :D

Here follows the testing.




 Room LED lights only!


 Room lighting plus two rows of strip LED's. Shadow caused by LED tubes on roof (room lighting)
This will not be a problem when plastic reflector goes on top of frame.


By the way train was driven here from top of old helix. Track working fine and all sections wired correctly allowing trains to proceed into Honeysuckle... YEIIII!!!!



 Room lighting on, rear strip LEDs only



Room lighting on, rear strip LED's only


 Room lights on, and one strip LED's on (Front)



Room lights on, and one strip LED's on (Front)


 Room lights off, and one strip LED's on (Front)




 Room lighting off, one rear strip on.(rear) Note shadow from roof LED's gone as well.


Room lighting turned off. Both LED strips on.

Edit I used plastic angle to mount LED's Had it on hand, thanks to Graeme S.





The air conditioner lifted temp from 11C to 21C in 15 minutes (at the back of room 15 m away) Much better than before the roof was repaired.
Cheers
Rod Young

2019/04/28

2019_04_28 Tradesman bitch!! and more wiring

2019_04_28   So what does a tradesman make an hour and what do you get?



About a year ago, I invited this guy to install my $2000 (huge) Panasonic Air Conditioner (Thanks Good Guys for a "Friday" discount,on top of an already great price which was hundreds under Harvey "GST" Norman.


When its on the drain drips over the doorway, straight down the back of your neck. The fix was to wrap it with insulating tape which fell off two days later. I thought that was what blue glue was for?



I was quoted $850 install, because a gap had to be cut into roof above air conditioner to allow air to enter at top. I cut hole and they used it to install the unit over door.  When I asked them to box it in, they went away for more materials.  Never saw them back again, however the bill arrived and was upped to $1580 for the extra work involved. They never came back. I paid them cash for job (Yes big mistake) I hope they paid GST because I asked the taxman to check if they did. They worked 3 hours. Well one guy did. The electrician was there for only an hour. So 4 hours into $1600 is about $400 an hour and I had to get another Tradesman (actually a real tradesman ) to finish the job.







Cutting the hole out properly (I am not a tradesman :blush: ) After removing the roof iron and insulation.



Build a box and seal it into the ceiling. Paint and voila!


Now the ceiling cavity can get hot or cold, and the airconditioner can circulate the warmed / cooled air and operate more economically. Thanks to my son Dale Young... A real tradesman.
Now as long as the door is not opened or closed as the large door flap drops down when AC turned on and off. The rest of the time it sits neatly out of the way.

Back to the Model Railway  :D




More wiring, and yesterday and today, I have continued on with the project to get this job finished and trains running again. Al and I started this on Thursday, last. the wiring is slowly progressing, and of course it is even slower as a one man operation. 

The big news is that I how have all six districts connected into the system, and the short circuit appears to be fixed.  No breaker alarms at all for a week Ha Ha.

Have a sound  loco advancing down the SG track as each dropper is connected. Out of shot a GM does same thing on the BG...    This is exciting!!

Cheers
Rod Young